0 votes
in ZTE by
edited
This Phone was Booting up to the MTN Logo

Then i ordered a Flashfile from this site and flashed it

Flashing completed nicely and i can flash the phone Number witout times

yet it cant boot But i can write and read the files in the phone.

What would be the Problem here

1 Answer

0 votes
by
Hi. This can happen if you flashed the Preloader as well or if the device had a hardware  (like RAM or EMMC) related issue and not software. I suggest you try a memory test on the SP Flash Tool and see if the two checks ohk. Kindly comment below with the results.
by
Here is the LOG AFTER I RUN THE TEST

============ Memory Detection Report ===========

Internal RAM:


External RAM:

    Type = DRAM

    Size = 0x20000000 (512MB/4096Mb)

NAND Flash:

    ERROR: NAND Flash was not detected!

EMMC:

     EMMC_PART_BOOT1     Size = 0x0000000000400000(4MB)
     EMMC_PART_BOOT2     Size = 0x0000000000400000(4MB)
     EMMC_PART_RPMB     Size = 0x0000000000400000(4MB)
     EMMC_PART_GP1     Size = 0x0000000000000000(0MB)
     EMMC_PART_GP2     Size = 0x0000000000000000(0MB)
     EMMC_PART_GP3     Size = 0x0000000000000000(0MB)
     EMMC_PART_GP4     Size = 0x0000000000000000(0MB)
     EMMC_PART_USER     Size = 0x00000000e9000000(3728MB)

UFS:

    ERROR: UFS was not detected!

============     RAM Test     ============

Data Bus Test:

[D0]
[D1]
[D2]
[D3]
[D4]
[D5]
[D6]
[D7]
[D8]
[D9]
[D10]
[D11]
[D12]
[D13]
[D14]
[D15]
[D16]
[D17]
[D18]
[D19]
[D20]
[D21]
[D22]
[D23]
[D24]
[D25]
[D26]
[D27]
[D28]
[D29]
[D30]
[D31]
OK!!

Address Bus Test:

[A1]
[A2]
[A3]
[A4]
[A5]
[A6]
[A7]
[A8]
[A9]
[A10]
[A11]
[A12]
[A13]
[A14]
[A15]
[A16]
[A17]
[A18]
[A19]
[A20]
[A21]
[A22]
[A23]
[A24]
[A25]
[A26]
[A27]
[A28]
OK!!

RAM Pattern Test :
Writing ...
    0x44332211,
    0xA5A5A5A5,
by
Ohk let the EMMC test complete as well and let see.
by
HERE IS WHAT AM GETTING

============ Memory Detection Report ===========

Internal RAM:


External RAM:

    Type = DRAM

    Size = 0x20000000 (512MB/4096Mb)

NAND Flash:

    ERROR: NAND Flash was not detected!

EMMC:

     EMMC_PART_BOOT1     Size = 0x0000000000400000(4MB)
     EMMC_PART_BOOT2     Size = 0x0000000000400000(4MB)
     EMMC_PART_RPMB     Size = 0x0000000000400000(4MB)
     EMMC_PART_GP1     Size = 0x0000000000000000(0MB)
     EMMC_PART_GP2     Size = 0x0000000000000000(0MB)
     EMMC_PART_GP3     Size = 0x0000000000000000(0MB)
     EMMC_PART_GP4     Size = 0x0000000000000000(0MB)
     EMMC_PART_USER     Size = 0x00000000e9000000(3728MB)

UFS:

    ERROR: UFS was not detected!

============     RAM Test     ============

Data Bus Test:

[D0]
[D1]
[D2]
[D3]
[D4]
[D5]
[D6]
[D7]
[D8]
[D9]
[D10]
[D11]
[D12]
[D13]
[D14]
[D15]
[D16]
[D17]
[D18]
[D19]
[D20]
[D21]
[D22]
[D23]
[D24]
[D25]
[D26]
[D27]
[D28]
[D29]
[D30]
[D31]
OK!!

Address Bus Test:

[A1]
[A2]
[A3]
[A4]
[A5]
[A6]
[A7]
[A8]
[A9]
[A10]
[A11]
[A12]
[A13]
[A14]
[A15]
[A16]
[A17]
[A18]
[A19]
[A20]
[A21]
[A22]
[A23]
[A24]
[A25]
[A26]
[A27]
[A28]
OK!!

RAM Pattern Test :
Writing ...
    0x44332211,
    0xA5A5A5A5,
by
Seems like the RAM pattern test is not completing. The problem could be there
by
IT COMPLETED AS FOLLOWS

RAM Pattern Test :
Writing ...
    0x44332211,
    0xA5A5A5A5,
    0xA5A5A500,
    0xA500A500,
    0xA5000000,
    0x00000000,
    0xFFFF0000,
    0xFFFFFFFF,
OK!!

Increment/Decrement Test:
Writing...
OK!!
Saroms HELP, where you can avail support on files purchased through saroms or request any other Chinese lowend firmware or file not yet listed on www.saroms.co.za.

Categories

...